大陸公司：廣東省東莞市東城街道長泰路東城段73號1棟102室
TEL/FAX:886-769-22314537
業務：13922974343 林經理
微信號：Joji_1998
Q Q:641563647
中文郵箱:twjoji88@126.com
臺灣公司：臺灣彰化縣鹿港鎮頭侖里捕尾巷2號
電話:00886-47615693
熱熔膠封盒機使用說明
本機器集電氣一體自動化控制生產、電氣元件采用優質產品性能穩定、生產速度40-50盒1分鐘，封盒規格（長×寬×高）（100-290）×（70-150）×（45-120）mm，裝機功率0.5-0.89KW（220V50HZ），源0.4mpa,0.3M3/min。
1. 工作原理：將盒子向里推，當盒子碰到行程開關1時，上膠氣缸自動上升，將膠水沾在盒子兩端。上膠氣缸設有磁感應開關，當氣缸上升至磁感應開關感應范圍氣缸會自動下落。同時頂盒氣缸上升，將盒子折疊成形。頂盒磁感應開關感應時氣缸會自動下落。當氣缸自動下落后，第二個盒子方可向里推。當盒子碰到行程開關2時，出盒氣缸開始工作，將盒子推向分流槽，當氣缸上升至磁感應開關感應范圍氣缸會自動下落。
2.簡單故障檢查 simple failure checking
|
故障現象 failure symptom |
檢查內容 check content |
|
機器不工作machine is out of work |
1. 電源插頭是否插入 the power plug whether insert 2. 電源開關是否打開 the power switch whether turn on 3. 氣壓是否正常 the air pressure whether normal 4. 檢查行程開關1是否工作 check the travel switch 1 whether work |
|
上膠后頂盒氣缸不工作 after gluing the jacking box air cylinder doesn’t work |
1. 檢查上膠磁感應開關是否工作 check the gluing magnetic induction switch whether work 2. 檢查頂盒電磁閥是否工作 check the jacking box electric magnetic valve whether work |
|
頂盒氣缸上升后不下落 jacking box air cylinder doesn’t fall after rise |
檢查頂盒磁感應開關是否工作 check the jacking box magnetic induction switch whether work |
|
出盒氣缸不工作 eject box air cylinder doesn’t work |
檢查行程開關2是否工作 check the travel switch 2 whether work |
|
出盒氣缸不下落 eject box air cylinder doesn’t fall |
檢查出盒磁感應開關是否工作 check the eject box magnetic induction switch whether work |
|
膠箱溫度失控 temperature of glue box is out of control |
1. 檢查電熱隅 check the thermo couple 2. 檢查加熱棒 check the heat stick 3. 如以上兩點均無問題，詳見溫控表使用說明書 if the above two points all without problem, please see the operate manual detail of the temperature controller meter |
|
上膠氣缸1和2未同步 gluing air cylinder 1 and 2 doesn’t synchronize |
調整氣缸兩端節流閥 adjust the both ends throttle valve of air cylinder |
應用案例范圍:
生產以熱熔膠廣泛用于家熱熔膠噴膠、涂膠、電子產品組裝、不干紙盒、膠貼包裝行業:紙箱包裝、飲料包裝，涂布復合行業: 等相關行業自動化設備。
Box sealing machine instructions
This machine combine electricity into one, automatic control production, electric component adopt the high quality products, steady performance ,production speed :40-50 boxes /one minute, sealing standard(L×W×H) （100-290）×（70-150）×（45-120）mm，install power 0.5-0.89KW（220V50HZ），air source 0.4mpa,0.3M3/minWorking principle : push the box inward, when the box touch the travel switch one ,gluing air cylinder will rise automatically to stick the glue on the both ends of box, gluing air cylinder with the magnetic induction switch ,when the air cylinder rise to the induction switch range ,air cylinder will fall automatically, meanwhile jacking box air cylinder rise ,fold the box into shape. When jacking box magnetic induction switch react, the air cylinder will fall automatically, after the air cylinder fall, the second box will be pushed inward. When the box touch the travel switch two, the eject box air cylinder starts to work , push the boxes to the distributary tank, when air cylinder rise to the induction range of magnetic induction switch, which will fall automatically.
中文站
英文站
